PDA

Visualizza versione completa : Masterizzare sotto DOS


Mr Wolf
24-05-2005, 10.59.38
C'è qualcuno che conosce un programma che permetta di masterizzare sotto ms-dos, in particolare da una partizione NTFS, dopo aver avviato con un floppy d'avvio?

dave4mame
24-05-2005, 11.07.28
la cosa diventa complicate, se non altro perchè per vedere la partizione NTFS devi caricare un driver di terze parti (tipo quelli della winternals).

per masterizzare sotto dos mi pare di ricordare che la goldenarrow (il produttore delle vecchie versione di cdrwin) avesse in catalogo un prodotto, ma il nome proprio non lo ricordo...

davlak
24-05-2005, 12.27.15
la goldenhawk continua a supportare il dos in alcune tools freeware:

http://www.goldenhawk.com/dos.htm

dave4mame
24-05-2005, 12.43.38
ecco... avevo sbagliato pure il nome del produttore :(

avevo in mente proprio DAO...

davlak
24-05-2005, 12.54.31
comunque nella cartella di installazione di Nero c'è un file DosBootimage.IMA che è buono per creare un floppy di avvio DOS con tutti i driver necessari per il burning sotto dos, compreso un reader NTFS che viene caricato di default.


il readme recita:


This bootable disk contains a DR-DOS 7.03, plus tools for FAT32 and NTFS
as well as for IDE, USB and FireWire(IEEE1394) CD-ROM and HDD access.
NOTE: Nero may try to change content of some included files, (e.g. DCONFIG.SYS),
so be careful if changing them.


About older FAT
---------------/
Of course, previous FAT partitions, as FAT16 are fully supported by DR-DOS
7.03.

About FAT32
-----------/
The FAT32 driver is loaded by default and no additional command is
required to access your FAT32 partition.

About NTFS
----------/
The loaded NTFS driver is a read-only driver. The NTFS partitions can
be accessed but any modification operations (like creating or deleting
file or diractory, copying) of this file system are not supported.

About USB HDD
-------------/
Also recognition of external USB hard disk drives as well as of USB memory sticks
is supported. The FAT resp. NTFS file system drivers will also search for FAT resp.
NTFS partitions on these external devices.

About IDE/SCSI CD-ROM
---------------------/
Unfortunately, SCSI CD-ROMs are not supported, because only IDE drives have a
generic driver (VIDE-CDD.SYS from OAK). SCSI depends from the SCSI controller,
and there is no generic driver available for DR-DOS and SCSI controllers.

About USB/IEEE1394 CD-ROM
-------------------------/
SCDD driver guidelines:
* When using an on-board USB/FireWire controller:
Some motherboards allow to disable IRQs for on-board devices via BIOS.
For SCDD to work, the IRQs for USB and FireWire controllers must be enabled.
* Some BIOSes allow ROM BIOS shadowing. This option must be turned off at least
for addresses D000-DFFF, because the FireWire controllers use this region for
i/o. Otherwise, the driver will be unable to initialize the FireWire controllers.
* To reserve letters for on-the-fly attachment of devices, specify the number
of letters to reserve with the /R command-line switch in dconfig.sys.
e.g. HIDEVICE=C:\SCDD.SYS /D:USBCD001 /R:2
* When reading from a device it is possible that sometimes the device's spindle
has not had the time to spin up to its proper speed. This may lead to small
delays (1-2 sec) before data is read, or a message may be displayed by DOS e.g.

Drive not ready. Abort, Retry, Fail?

We recommend to retry the operation several times (Retry).

About assigned drive letters
----------------------------/
The drive letters are assigned in order the particular driver are loaded and starting
with the next free drive letter:
1. All FAT16 Partitions beginning with C:
2. All FAT32 Partitions
3. All NTFS Partitions
4. All IDE CD-ROM drives
5. All USB/IEEE1394 CD-ROM drives

davlak
24-05-2005, 15.13.58
ho ri-trovato un link interessante

http://www.freeweb.hu/doscdroast/

Mr Wolf
24-05-2005, 16.21.45
AZZZZ!!
Grazie a tutti!

Ma...il file DosBootimage.IMA va masterizzato su CD?

davlak
24-05-2005, 16.26.05
lo puoi usare per creare un cd di avvio, con Nero, come file immagine (ti chiede il percorso alla prima finestra e gli dai quello del .ima)
oppure un floppy di avvio, ma per poterlo scrivere su floppy ti serve un programma tipo winimage o ultraiso e simili.